Guide · Homeowners · 4 min read · Updated 17 November 2026
How to Replace a Broken Stair Spindle: Step-by-Step Guide
Short answer
To replace a broken stair spindle, remove the fillets holding it in the handrail and baserail, cut out the old spindle, measure the rake angle, cut the new spindle to the same length and angle, glue and pin it in place, and refit the fillets. On cut-string stairs, the spindle fits into the tread instead. A joiner typically charges £90–£180 for one or two spindles.
First, identify your staircase type
How a spindle is fixed depends on the stair. On a closed-string staircase, the side of the stair is a solid board that hides the ends of the treads, and the spindles stand on a baserail or capping fixed to its top. The spindles sit in a groove in the underside of the handrail and the top of the baserail, held in place by short timber infills called fillets. This is the most common type in modern UK homes and the easiest to work on.
On a cut-string staircase, the side board is cut to the shape of the steps, the treads overhang it, and the spindles are fixed directly into the treads, often two per tread. In older homes they may be set into dovetails in the tread ends, hidden behind a return nosing. Replacing these takes more care.
A quick way to tell: look at the side of the stair from the hallway. If you see a straight board running diagonally with the treads hidden behind it, it is a closed string. If you see the stepped outline of each tread and riser, it is a cut string.
Tools and materials
For a typical closed-string spindle repair, you need very little, but accuracy matters. The new spindle must match the old one in profile and section size, commonly 32 mm or 41 mm square stock on modern stairs.
- Replacement spindle matching the profile and section size
- Fillets to suit the groove width, if the old ones split
- Sliding bevel to copy the rake angle
- Fine-toothed saw or mitre saw
- Wood glue and small panel pins or screws
- Chisel, hammer and nail punch
- Filler, sandpaper and matching paint or stain
Step by step on a closed-string stair
Carefully prise out the fillets either side of the broken spindle at the top and bottom, using a chisel to lever them gently so they can be reused if they are in good condition. Cut through the broken spindle in the middle and twist out each half. Clean dried glue and old pins out of the grooves. Measure the vertical length between the handrail and baserail grooves, and set a sliding bevel to the angle of the rail so the new spindle's ends can be cut to match.
Cut the new spindle slightly long and test it, trimming until it fits snugly without forcing the rails apart. Apply glue to both ends, set it in position, check it is plumb with a level, and pin it through the ends into the rail. Refit or replace the fillets with glue and pins, punch the pins below the surface, fill and sand. Finish with primer and paint, or stain and lacquer, to match.
Cut-string stairs and older balustrades
On a cut-string stair, the spindle base usually sits in a hole drilled in the tread or in a dovetail housing at the tread end. Dovetailed spindles are reached by removing the return nosing, a small moulding on the end of the tread, which is often glued and pinned. Once that is off, the broken spindle can be removed, and a new one shaped to fit the dovetail. At the top, the spindle is usually set into a hole or mortice in the handrail.
Period stairs need a lighter touch. Old timber is dry and brittle, glue joints may be animal glue, and the turned profiles rarely match modern stock. Removing a return nosing without splitting it, and making a dovetail that fits cleanly, is skilled work. In listed buildings, check consent requirements before altering anything.
DIY or call a joiner?
Replacing a single stock spindle on a closed-string stair is a reasonable DIY job if you have basic tools and patience. The common problems are cutting the angle wrong, leaving the spindle loose so it rattles, splitting fillets and over-sanding the paint around the repair. Cut-string stairs, period spindles, several spindles at once, or a balustrade that is loose overall are better left to a joiner, who will also check the handrail, newels and gaps while on site.
The table summarises when DIY tends to work and when it is worth paying for a professional.
| Situation | DIY suitability | Why |
|---|---|---|
| One stock spindle, closed string | Usually fine | Simple fillet fixing, standard profile |
| Several spindles, closed string | Possible but slow | Consistent angles and spacing take time |
| Cut-string with dovetails | Joiner recommended | Return nosings and dovetails are delicate |
| Period or turned spindles | Joiner recommended | Profiles may need copying |
| Loose handrail or newel | Joiner recommended | Structural fixings need checking |
Safety while the spindle is out
A missing spindle leaves a gap a small child can fall through, so do not leave a balustrade open overnight with children in the house. If you cannot finish the job, fix a temporary board across the gap. When the work is done, check that the gap between the new spindle and its neighbours is less than 100 mm, in line with Approved Document K. We arrange spindle repairs through vetted local joiners, often as a short single visit.
Finally, give glue time to cure before anyone leans on the balustrade, and check the spindle is firm the next day.
Questions people also ask
What holds stair spindles in place?
On closed-string stairs, spindles sit in grooves in the handrail and baserail, held by small timber fillets glued and pinned between them. On cut-string stairs, they fit into holes or dovetails in the treads and into holes in the handrail. Glue and pins or screws secure the ends.
Why do stair spindles come loose?
Usually because glue joints have failed with age, timber has shrunk, pins have worked loose or the spindle has been knocked repeatedly. A loose handrail or newel also lets spindles rattle. Re-gluing and pinning often fixes single spindles, but a loose balustrade should be checked by a joiner.
What size are stair spindles?
Modern UK stair spindles are commonly 32 mm or 41 mm square in section, in lengths around 900 mm to 1,100 mm, cut to size on site. Period spindles vary widely. Always measure your existing spindle's section and profile before buying a replacement.
Written and checked by the Spindle Replacement team. Read our editorial policy.
More guides
How Much Does Stair Spindle Replacement Cost in the UK?
Replacing one or two broken stair spindles typically costs £90–£180 fitted. A full re-spindle of a straight stair and landing in pine or hemlock runs…
Stair Spindle Gap Regulations UK: The 100 mm Rule Explained
Under Approved Document K, guarding on stairs and landings should not let a 100 mm sphere pass through any opening, so the clear gap between spindles…
Oak vs Metal vs Glass Stair Spindles: Which Should You Choose?
Painted pine or hemlock is the cheapest re-spindle at £550–£1,100 for a straight stair and landing. Solid oak spindles cost £850–£1,700, metal…
Matching Victorian and Edwardian Stair Spindles: A Guide
Original Victorian, Edwardian and 1930s spindles rarely match modern stock profiles, so the best route is usually a turned copy made from an…
Get a free spindle replacement quote
Tell us what you need and we'll come back with a clear price.
Request a quote